国产三级大片在线观看_久久96热在精品国产三级_九九久久99精品_成年黄网站色大免费全看

美國VTI手套箱微量水分析儀探頭MK-XTR-100使用注意事項|埃登威自動化系統設備（上海）有限公司

美國VTI手套箱微量水分析儀探頭MK-XTR-100使用注意事項


注意：用于刷新濕度傳感器功能的磷酸溶液具有腐蝕性。請戴防護手套和護目鏡。
1從手套箱中卸下水分分析儀之前，請斷開系統電纜

2從濕度探頭上擰下護罩（防護罩）蓋。

三。在傳感器探頭上涂抹蒸餾水。用無絨布擦干（不要用紙巾）。小心操作探頭。避免過度接觸探頭表面。美國VTI手套箱微量水分析儀探頭MK-XTR-100使用注意事項
4在旋轉裝置的同時，將10到15滴磷酸溶液直接滴在探頭上，使傳感器濕潤。將足夠的溶液滴到探頭上，直到表面完全覆蓋。
讓傳感器風干四小時。在探針下方放置一塊滴布，以收集多余的酸。
（©）真空技術公司，美國馬薩諸塞州格洛斯特市大共和國大道15號，郵編：01930，2016年
5完全干燥后，更換探頭上的保護罩。
6在拆下法蘭蓋并更換端口中的傳感器之前，確認手套箱仍在+5 mBar到+8 mBar的壓力范圍內。
7將水分分析儀重新安裝到手套箱后，重新連接系統電纜。美國VTI手套箱微量水分析儀探頭MK-XTR-100使用注意事項
8在觸摸屏上，觸按“Analyzer”以激活水分分析儀。
9記錄濕度數據

注：在鋰電池和有機金屬應用中，操作過程中揮發的酸/堿會腐蝕濕度傳感器，從而導致電阻變化。顯示的濕度值可能與實際濕度值不同。偏差程度取決于腐蝕性物質的濃度以及傳感器刷新過程的徹底性。在這種情況下，我們建議在保修期內將分析儀發送給我們進行免費校準。


Maintenance of the Moisture Analyzer

Attention: The phosphoric acid solution used for refreshing the functionality of the moisture sensor is corrosive. Please wear protective gloves and eyewear.

  1. Disconnect the system cable before removing the moisture analyzer from the glove box

  2. Unscrew the shroud (protective cage) cover from the moisture probe.

  3. Apply distilled water on the sensor probe. Dry with a lint-free cloth (do not use paper towels). Handle the probe with care. Avoid excessive contact the surface of the probe.美國VTI手套箱微量水分析儀探頭MK-XTR-100使用注意事項

  4. Moisten the sensor with the phosphoric acid solution by slowly dripping 10 to 15 drops directly on the probe while rotating the unit. Drip enough of the solution onto the probe until the surface is completely covered.

    Allow the sensor to air-dry for four hours. Place a drop cloth under the probe to catch excess acid.

page1image8664page1image9760page1image9928page1image10096

(©)Vacuum Technology Inc., 15 Great Republic Drive, Gloucester, MA, 01930 USA 2016


  1. When completely dry, replace the protective shroud on the probe.

  2. Confirm that the glove box is still within the pressure range of +5 mBar to +8 mBar before removing the blind flange cover and replacing the sensor in the port.

  3. Reconnect the system cable after the moisture analyzer is reinstalled in the glove box.

  4. On the touchscreen, touch “Analyzer” to activate the moisture analyzer.

  5. Log the moisture data

    Note: In lithium battery and in organometallic applications, volatilized acid/alkali during operation will corrode the moisture sensor which can cause a change in electrical resistance. The displayed moisture value might be different from the actual moisture value. The degree of deviation depends on the concentration of corrosive substances as well as the thoroughness of the sensor-refreshing process. In this case, we recommend sending the analyzer to us for a free calibration within the warranty period.


更多美國VTI手套箱微量水分析儀探頭MK-XTR-100使用注意事項信息請直接致電埃登威上海021-55581219產品：微量氧分析儀,藥品殘氧儀,露點儀,熱導氣體分析儀,GE流量計,OX-1氧傳感器,頂空分析儀,紅外氣體分析儀,高溫濕度儀,西門子U23分析儀,ppb微量水分析儀,OXY.IQ氧分析儀,煙氣濕度儀,燃?xì)鉄嶂祪x,Kaye溫度驗證儀,L&W白度,儀激光氧分析儀,壓縮空氣露點儀,干燥機露點儀,激光氣體分析儀,便攜式露點儀,便攜式微量氧分析儀，F(xiàn)ei （維修中心，代表處，總代理，分公司，子公司，售后中心，銷售中心，上海辦，辦事處在哪里）

滬公網安備 31010902002456號